EN 10243-1 PDF

DIN EN – Free download as PDF File .pdf), Text File .txt) or read online for free. Find the most up-to-date version of DIN EN at Engineering Buy DIN EN STEEL DIE FORGINGS – TOLERANCES ON DIMENSIONS – PART 1: DROP AND VERTICAL PRESS FORGINGS.

Author: Akirg Shakamuro
Country: Rwanda
Language: English (Spanish)
Genre: Relationship
Published (Last): 22 June 2014
Pages: 230
PDF File Size: 6.74 Mb
ePub File Size: 16.40 Mb
ISBN: 859-7-57615-368-6
Downloads: 78429
Price: Free* [*Free Regsitration Required]
Uploader: Goltilar

In such cases the factor S4 is used; the weight to be taken into consideration is only that of a 10243–1 having diameter d and height e.

EN 10243-1.pdf

While grade E close tolerances may be applied to all dimensions on one forging, wn is more economical to apply them only to those specific dimensions on which closer tolerances are essential. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.

Summary of pagesThis document comprises a front cover, an inside front cover, the EN title page, pages 2 to 34, an inside back cover and a back cover. The shape complexity factor of a forging is the ratio of the mass of the forging to the mass1 of the enveloping shape necessary to accommodate the maximum dimensions of the forging: If 01243-1 category of steel used is M2, the heavy diagonal line is followed downward to the point of intersection with the vertical line M2 and the horizontal line thus met is followed to the right i.

Pieces forgees par estampage en acier. The application of such tolerances should be kept to a minimum and, in these instances, the tolerances shall be 102433-1 clearly against the appropriate dimension s on the forging drawing.

A similar een is followed for the factor of shape complexity so that downward displacement of the horizontal line used is nil, one place, two places and three places for factors S1, S2, S3 and S4 respectively.

  CORPORATE CHANAKYA BY RADHAKRISHNAN PILLAI FREE PDF

Requirements for carbon, carbon manganese and alloy hot worked or cold finished steels. The residual flash is measured from the body of the forging to the trimmed edge of the flash, as indicated in Figure Above 0,16 up to and including 0,32; S2: You may experience issues viewing this site in Internet Explorer 9, 10 or As a general rule grade F tolerances result in a cheaper forged component.

ISO 3, Preferred numbers Series of preferred numbers. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Marchand conflicting national standards shall be withdrawn at the latest by March Where restrictions in deviations of form have been agreed, these will be to ISO and noted on the drawing.

Only tolerances to grade F shall be applied. These two grades of tolerances are identified as follows: Tolerances for heavier or larger forgings shall be agreed at the time of enquiry and order.

This should be done to obviate unnecessary minor variations between tolerances, thus facilitating drawing preparation and simplifying inspection procedures. Instances occur in which this tolerance is inadequate. All forgings bear the CDP identification mark, unless a different 1 Documents.

Warm hergestellt in Haermmern und Eb. Please download Chrome or Firefox 1024-31 view our browser tips. Compliance with a British Standard does not of itself confer immunity from legal obligations. The enveloping shape of a circular forging is the circumscribing cylinder, the mass of which is calculated from the formula see Figure 2: Mismatch tolerances are applied independently of any other tolerances. Considerations of this nature, whilst frequently encountered, are highly individual, and vary widely.

  CLOB X BULA PDF

The tolerance grade and tolerances given on the drawings are examples only and should not be regarded as either mandatory, recommended or minimum requirements since in practice the tolerances will depend on both the capability of the forging equipment and the requirements of the purchaser. The supplier will draw the attention of the purchaser to such instances and it will be necessary to negotiate greater tolerances on the draft angle surfaces to meet these circumstances.

Flatness tolerances relate to deviations of surfaces from the specified contour.

BS EN – Steel die forgings. Tolerances on dimensions. Drop and vertical press forgings

ISOTechnical drawings Fundamental tolerancing principle. The nominal diameter and the location of ejector marks will be indicated to the purchaser on the forging drawing before the commencement of production.

We use cookies to make our website easier to use and to better understand your needs. Dimensional checks regarding depth of scale pits or any other point in question should be made in relation to the machining locations.

Base all thickness tolerances except those for overall thickness on dimension t shown above. See us on booth at NPE Documents. This publication does not purport to include all the necessary provisions of a contract.

When straightness tolerances or flatness tolerances are required, this shall be indicated on the agreed forging drawing. The minus tolerances do not apply to edge radii up to and including 3 mm when such radii are affected by subsequent removal of draft by trimming or punching.

Posted in: Sex